Datasheet - DILM400-S/22(220-240V50/60HZ)

Product range

Contactors

Application

Contactors for Motors

Subrange

Standard devices greater than 170 A

Utilization category

AC-1: Non-inductive or slightly inductive loads, resistance furnaces
NAC-3: Normal AC induction motors: starting, switch off during running
AC-4: Normal AC induction motors: starting, plugging, reversing, inching

Connection technique

Screw connection

Rated operational current

AC-3

380 V 400 V

I_e

400

AC-1

Conventional free air thermal current, 3 pole, 50 - 60 Hz

Open

at 40 °C

I_th=I_e

612

enclosed

I_th

450

Conventional free air thermal current, 1 pole

open

I_th

1250

enclosed

I_th

1125

Max. rating for three-phase motors, 50 - 60 Hz

AC-3

220 V 230 V

125

380 V 400 V

212

660 V 690 V

300

1000 V

132

AC-4

220 V 230 V

380 V 400 V

160

660 V 690 V

240

1000 V

132

Contact sequence

${#text_magnify#}$

Can be combined with auxiliary contact

DILM820-XHI…

Actuating voltage

220 - 240 V 50/60 Hz

Voltage AC/DC

AC operation

Contacts

N/O = Normally open

2 N/O

N/C = Normally closed

2 NC

Auxiliary contacts

possible variants at auxiliary contact module fitting options

on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA

Side mounting auxiliary contacts

${#text_magnify#}$

Instructions

integrated suppressor circuit in actuating electronics
660 V, 690 V or 1000 V: not directly reversing

Notes

DILM…-S power contactors are actuated traditionally
${#text_magnify#}$
① Stopping in the event of an emergency (emergency switching off)

General
Standards			IEC/EN 60947, VDE 0660, UL, CSA
Lifespan, mechanical
AC operated	Operations	x 10⁶	7
Operating frequency, mechanical
AC operated	Operations/h		2000
Climatic proofing			Damp heat, constant, to IEC 60068-2-78 Damp heat, cyclic, to IEC 60068-2-30
Ambient temperature
Open		°C	-40 - +60
Enclosed		°C	- 40 - + 40
Storage		°C	- 40 - + 80
Mounting position			${#text_magnify#}$ ${#text_magnify#}$
Mechanical shock resistance (IEC/EN 60068-2-27)
Half-sinusoidal shock, 10 ms
Main contacts
N/O contact		g	10
Auxiliary contacts
N/O contact		g	10
N/C contact		g	8
Degree of Protection			IP00
Protection against direct contact when actuated from front (EN 50274)			Finger and back-of-hand proof with terminal shroud or terminal block
Weight
AC operated		kg	8.42
DC operated		kg	8.42
Weight		kg	8.42
Terminal capacity main cable
Flexible with cable lug		mm²	50 - 240
Stranded with cable lug		mm²	70 - 240
Solid or stranded		AWG	2/0 - 500 MCM
Flat conductor	Lamellenzahl x Breite x Dicke	mm	Fixing with flat cable terminal or cable terminal blocks See terminal capacity for cable terminal blocks
Busbar	Width	mm	25
Main cable connection screw/bolt			M10
Tightening torque		Nm	24
Terminal capacity control circuit cables
Solid		mm²	1 x (0.75 - 2.5) 2 x (0.75 - 2.5)
Flexible with ferrule		mm²	1 x (0.75 - 2.5) 2 x (0.75 - 2.5)
Solid or stranded		AWG	18 - 14
Control circuit cable connection screw/bolt			M3.5
Tightening torque		Nm	1.2
Tool
Main cable
Width across flats		mm	16
Control circuit cables
Pozidriv screwdriver		Size	2
Main conducting paths
Rated impulse withstand voltage	U_imp	V AC	8000
Overvoltage category/pollution degree			III/3
Rated insulation voltage	U_i	V AC	1000
Rated operational voltage	U_e	V AC	1000
Safe isolation to EN 61140
between coil and contacts		V AC	500
between the contacts		V AC	500
Making capacity (p.f. to IEC/EN 60947)		A	5500
Breaking capacity
220 V 230 V		A	5000
380 V 400 V		A	5000
500 V		A	5000
660 V 690 V		A	5000
1000 V		A	950
Component lifespan
			AC1: See → Engineering, characteristic curves AC3: See → Engineering, characteristic curves AC4: See → Engineering, characteristic curves
Short-circuit rating
Short-circuit protection maximum fuse
Type “2” coordination
400 V	gG/gL 500 V	A	500
690 V	gG/gL 690 V	A	500
1000 V	gG/gL 1000 V	A	200
Type “1” coordination
400 V	gG/gL 500 V	A	630
690 V	gG/gL 690 V	A	630
1000 V	gG/gL 1000 V	A	250
AC
AC-1
Rated operational current
Conventional free air thermal current, 3 pole, 50 - 60 Hz
Open
at 40 °C	I_th=I_e	A	612
at 50 °C	I_th=I_e	A	548
at 55 °C	I_th=I_e	A	522
at 60 °C	I_th=I_e	A	500
enclosed	I_th	A	450
Notes			At maximum permissible ambient air temperature.
Conventional free air thermal current, 1 pole
Note			at maximum permissible ambient air temperature
open	I_th	A	1250
enclosed	I_th	A	1125
AC-3
Rated operational current
Open, 3-pole: 50 – 60 Hz
220 V 230 V	I_e	A	400
240 V	I_e	A	400
380 V 400 V	I_e	A	400
415 V	I_e	A	400
440V	I_e	A	400
500 V	I_e	A	400
660 V 690 V	I_e	A	325
1000 V	I_e	A	95
Motor rating	P	kWh
220 V 230 V	P	kW	125
240V	P	kW	132
380 V 400 V	P	kW	212
415 V	P	kW	232
440 V	P	kW	250
500 V	P	kW	280
660 V 690 V	P	kW	300
1000 V	P	kW	132
AC-4
Rated operational current
Open, 3-pole: 50 – 60 Hz
220 V 230 V	I_e	A	296
240 V	I_e	A	296
380 V 400 V	I_e	A	296
415 V	I_e	A	296
440 V	I_e	A	296
500 V	I_e	A	296
660 V 690 V	I_e	A	260
1000 V	I_e	A	95
Motor rating	P	kWh
220 V 230 V	P	kW	92
240 V	P	kW	100
380 V 400 V	P	kW	160
415 V	P	kW	176
440 V	P	kW	186
500 V	P	kW	210
660 V 690 V	P	kW	240
1000 V	P	kW	132
Condensor operation
Individual compensation, rated operational current I_e of three-phase capacitors
Open
up to 525 V		A	307
690 V		A	177
Max. inrush current peak		x I_e	30
Component lifespan	Operations	x 10⁶	0.1
Max. operating frequency		Ops/h	200
DC
Rated operational current, open
DC-1
Notes			see DILDC300/DILDC600 or on request
Current heat loss
3 pole, at I_th (60°)		W	58
Current heat loss at I_e to AC-3/400 V		W	37
Magnet systems
Voltage tolerance
U_S			220 - 240 V 50/60 Hz
AC operated	Pick-up	x U_S	0.85 x U_{S min} - 1.1 x U_{S max}
AC operated	Drop-out	x U_S	0.2 x U_{S min} - 0.4 x U_{S max}
Power consumption of the coil in a cold state and 1.0 x U_S
Note on power consumption			Control transformer with u_k ≦ 10%
Pull-in power	Pick-up	VA	715
Pull-in power	Pick-up	W	645
Sealing power	Sealing	VA	6.8
Sealing power	Sealing	W	4
Duty factor		% DF	100
Changeover time at 100 % U_S (recommended value)
Main contacts
Closing delay		ms	55
Opening delay		ms	50
Behaviour in marginal and transitional conditions
Sealing
Voltage interruptions
(0 … 0.2 x U_{c min}) ≦ 10 ms			Time is bridged successfully
(0 … 0.2 x U_{c min}) > 10 ms			Drop-out of the contactor
Voltage drops
(0.2 … 0.6 x U_{c min}) ≦ 12 ms			Time is bridged successfully
(0.2 … 0.6 x U_{c min}) > 12 ms			Drop-out of the contactor
(0.6 … 0.7 x U_{c min})			Contactor remains switched on
Excess voltage
(1.15 … 1.3 x U_{c max})			Contactor remains switched on
Pick-up phase
(0 … 0.7 x U_{c min})			Contactor does not switch on
(0.7 x U_{c min}… 1.15 x U_{c max})			Contactor switches on with certainty
Admissible transitional contact resistance (of the external control circuit device when actuating A11)		mΩ	≦ 500
Electromagnetic compatibility (EMC)
Electromagnetic compatibility			This product is designed for operation in industrial environments (environment A). Its use in residential environments (environment 1) may cause radio-frequency interference, requiring additional noise suppression measures.
Rating data for approved types
Switching capacity
Maximum motor rating
Three-phase
200 V 208 V		HP	125
230 V 240 V		HP	150
460 V 480 V		HP	300
575 V 600 V		HP	400
General use		A	450
Auxiliary contacts
Pilot Duty
AC operated			A600
DC operated			P300
General Use
AC		V	600
AC		A	15
DC		V	250
DC		A	1
Short Circuit Current Rating		SCCR
Basic Rating
SCCR		kA	30
max. Fuse		A	800
max. CB		A	600
480 V High Fault
SCCR (fuse)		kA	30/100
max. Fuse		A	800/600 Class J
SCCR (CB)		kA	100
max. CB		A	600
600 V High Fault
SCCR (fuse)		kA	30/100
max. Fuse		A	800/600 Class J
SCCR (CB)		kA	30
max. CB		A	600
Special Purpose Ratings
Definite Purpose Ratings (100,000 cycles acc. to UL 1995)
LRA 480V 60Hz 3phase		A	3300
FLA 480V 60Hz 3phase		A	550
LRA 600V 60Hz 3phase		A	3120
FLA 600V 60Hz 3phase		A	420

Technical data for design verification
Rated operational current for specified heat dissipation	I_n	A	400
Heat dissipation per pole, current-dependent	P_vid	W	12.33
Equipment heat dissipation, current-dependent	P_vid	W	0
Static heat dissipation, non-current-dependent	P_vs	W	3.3
Heat dissipation capacity	P_diss	W	0
Operating ambient temperature max.		°C	-40
Operating ambient temperature max.		°C	60
IEC/EN 61439 design verification
10.2 Strength of materials and parts
10.2.2 Corrosion resistance			Meets the product standard's requirements.
10.2.3.1 Verification of thermal stability of enclosures			Meets the product standard's requirements.
10.2.3.2 Verification of resistance of insulating materials to normal heat			Meets the product standard's requirements.
10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects			Meets the product standard's requirements.
10.2.4 Resistance to ultra-violet (UV) radiation			Meets the product standard's requirements.
10.2.5 Lifting			Does not apply, since the entire switchgear needs to be evaluated.
10.2.6 Mechanical impact			Does not apply, since the entire switchgear needs to be evaluated.
10.2.7 Inscriptions			Meets the product standard's requirements.
10.3 Degree of protection of ASSEMBLIES			Does not apply, since the entire switchgear needs to be evaluated.
10.4 Clearances and creepage distances			Meets the product standard's requirements.
10.5 Protection against electric shock			Does not apply, since the entire switchgear needs to be evaluated.
10.6 Incorporation of switching devices and components			Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections			Is the panel builder's responsibility.
10.8 Connections for external conductors			Is the panel builder's responsibility.
10.9 Insulation properties
10.9.2 Power-frequency electric strength			Is the panel builder's responsibility.
10.9.3 Impulse withstand voltage			Is the panel builder's responsibility.
10.9.4 Testing of enclosures made of insulating material			Is the panel builder's responsibility.
10.10 Temperature rise			The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.11 Short-circuit rating			Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.12 Electromagnetic compatibility			Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function			The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.

Low-voltage industrial components (EG000017) / Power contactor, AC switching (EC000066)
Electric engineering, automation, process control engineering / Low-voltage switch technology / Contactor (LV) / Power contactor, AC switching (ecl@ss8.1-27-37-10-03 [AAB718012])
Rated control supply voltage Us at AC 50HZ	V	220 - 240
Rated control supply voltage Us at AC 60HZ	V	220 - 240
Rated control supply voltage Us at DC	V	0 - 0
Voltage type for actuating		AC
Rated operation current Ie at AC-1, 400 V	A	612
Rated operation current Ie at AC-3, 400 V	A	400
Rated operation power at AC-3, 400 V	kW	200
Rated operation current Ie at AC-4, 400 V	A	296
Rated operation power Ie at AC-4, 400 V	kW	160
Modular version		No
Number of auxiliary contacts as normally open contact		2
Number of auxiliary contacts as normally closed contact		2
Type of electrical connection of main circuit		Rail connection
Number of normally closed contacts as main contact		0
Number of main contacts as normally open contact		3

Product Standards			IEC/EN 60947-4-1; UL 60947-4-1; CSA - C22.2 No. 60947-4-1-14; CE marking
UL File No.			E29096
UL Category Control No.			NLDX
CSA File No.			012528
CSA Class No.			3211-04
North America Certification			UL listed, CSA certified
Specially designed for North America			No

${#text_magnify#}$
on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA
${#text_magnify#}$
Normal switching duty Normal AC induction motor Operating characteristics Switch on: from stop Switch off: during run Electrical characteristics: Switch on: up to 6 x Rated motor current Switch off: up to 1 x Rated motor current Utility category 100 % AC-3 Typical Applications Compressors Lifts Mixers Pumps Escalators Agitators fan Conveyor belts Centrifuges Hinged flaps Bucket-elevator Air-conditioning systems General drives for manufacturing and processing machines
${#text_magnify#}$
Extreme switching duty Squirrel-cage motor Operating characteristics Inching, plugging, reversing Electrical characteristics Make: up to 6 x rated motor current Break: up to 6 x rated motor current Utilization category 100 % AC-4 Typical applications Printing presses Wire-drawing machines Centrifuges Special drives for manufacturing and processing machines
${#text_magnify#}$
Switching conditions for 3 pole, non-motor loads Operating characteristics Non inductive and slightly inductive loads Electrical characteristics Switch on: 1 x rated operational current Switch off: 1 x rated operational current Utilization category 100 % AC-1 Typical examples of application Electric heat
${#text_magnify#}$
Short-time loading, 3-pole Time interval between two loading cycles: 15 minutes

${#text_magnify#}$
① DILM820-XHI11(V)-SI ② DILM820-XHI11-SA

Product-specific CAD data

3D Preview

IL03406002Z (AWA2100-1639) Contactors >170 A

IL03406002Z (AWA2100-1639) Contactors >170 A

IL03406005Z (AWA2100-2212) Contactors >170 A

IL03406005Z (AWA2100-2212) Contactors >170 A

UL/CSA: Approved rating data

UL/CSA: UL/CSA: Short Circuit Current Rating (SCCR)

Switchgear of Power Factor Correction Systems

X-Start - Modern Switching Installations Efficiently Fitted and Wired Securely

Mirror Contacts for Highly-Reliable Information Relating to Safety-Related Control Functions

Effect of the Cabel Capacitance of Long Control Cables on the Actuation of Contactors

Motor starters and "Special Purpose Ratings" for the North American market

Switchgear for Luminaires

Standard Compliant and Functionally Safe Engineering Design with Mechanical Auxiliary Contacts

The Interaction of Contactors with PLCs

Busbar Component Adapters for modern Industrial control panels

	Contactor, 3p+2N/O+2N/C, 200kW/400V/AC3
	Part no.	DILM400-S/22(220-240V50/60HZ)
	Catalog No.	274196
	Eaton Catalog No.	XTCS400M22B
	EL-Nummer (Norway)	4110263